3 in 1 vs 4 in 1 Tap: Which Boiling Water Tap Do You Need?
A 3 in 1 tap delivers boiling, hot and cold water from one spout. A 4 in 1 does the same and adds a fourth type of water, usually filtered or chilled, depending on the brand. If you only want the kettle gone, a 3 in 1 does the whole job. If you want cold drinking water on demand too, the 4 in 1 is the tap to fit. Our Zip HydroTap range covers both, so you can match the tap to the kitchen or office rather than the other way round.
This guide explains what each tap does, what sits under the sink, what each costs, what installation involves and how to decide for a home, a small office or a larger workplace.
TL;DR
- 3 in 1: boiling, hot and cold water from one tap. It replaces your kettle and your mixer tap.
- 4 in 1: everything a 3 in 1 does, plus a fourth water type. Check which one the model offers, because it differs by brand: filtered, chilled or sparkling.
- Choose a 3 in 1 if boiling water is the priority and you want the simplest set-up. Choose a 4 in 1 if people drink a lot of cold water, or if you want to remove the jug and bottled water from the routine.
- Plan the space first. Both need a unit under the sink, and the 4 in 1 usually needs room for a chiller or filter as well.
- Have it fitted by a qualified plumber. Boiling water and expensive kit are a poor mix for DIY.
Table of Contents
- What a 3 in 1 tap actually does
- What the fourth function adds
- 3 in 1 vs 4 in 1 at a glance
- Which one suits your situation
- Check the space under the sink
- What they cost to buy
- What they cost to run
- Filters, scale and looking after the tap
- Installation and safety
- A simple way to decide
- Where to buy your boiling water tap
- Our view
- FAQ
- Sources
What a 3 in 1 tap actually does
A 3 in 1 boiling water tap provides boiling, hot and cold water from a single tap in place of your existing kitchen tap. The boiling water comes from a small insulated tank fitted in the cupboard below, which keeps water at temperature so it is ready when you turn the handle. The hot and cold side works like a normal mixer, so you still fill the sink and rinse the pans as before.
In practice that means:
- Tea, coffee, instant noodles, baby bottle preparation and soup stock without waiting for a kettle.
- A clear worktop, because the kettle goes.
- Boiling water for softening stuck-on food or sterilising a chopping board.
Our Zip range includes this layout in models described as Boiling Plus Hot & Cold, such as the Zip Classic Plus HydroTap with Arc Mixer 240/175 G5 Boiling Plus Hot & Cold and the Zip Touch-Free Wave HydroTap with Arc Mixer 160/175 G5. The touch-free Wave versions suit places where many hands use the tap, such as an office kitchen or a staff room.
What the fourth function adds
The number in the name counts the types of water the tap can supply. A 4 in 1 gives you the three above and one more. That fourth type is not the same across the market. Some taps add filtered cold drinking water, some add chilled water and some add sparkling. Always read the product title and specification rather than assuming the number tells you the extra feature.

On our side, the Zip Classic Plus All-in-One HydroTap 240/175 G5 Boiling Chilled Plus Hot & Cold delivers boiling, chilled, hot and cold water. The 100/75 version of the same All-in-One HydroTap gives you the same four outlets in a different capacity. The Zip Classic Plus HydroTap with Arc Mixer G5 Boiling Chilled Plus Hot & Cold pairs the same functions with an arc mixer spout.
The benefit of the fourth function is simple: a glass of properly cold water straight from the tap. No jug in the fridge, no bottles to carry in and no bin full of plastic. In a busy workplace, that is the function people use most after the boiling water.
3 in 1 vs 4 in 1 at a glance
| 3 in 1 | 4 in 1 | |
|---|---|---|
| Water types | Boiling, hot, cold | Boiling, hot, cold plus a fourth (filtered, chilled or sparkling, by brand) |
| Replaces | Kettle and mixer tap | Kettle, mixer tap and, depending on the model, the water jug or bottled water |
| Under the sink | Boiler unit | Boiler unit plus the equipment for the fourth function |
| Best for | Homes, small kitchens, anyone who mainly wants boiling water | Families, offices, break rooms, anyone drinking lots of cold water |
| Upfront cost | Lower | Higher |
| Running cost | Lower, with no cooling to power | Slightly higher, because the extra function takes energy |
The cost row is the general pattern across the market. Exact prices are on each product page, so check the model you are looking at.
Which one suits your situation
A family kitchen at home
If you boil the kettle five or six times a day and drink tap water from a glass, a 3 in 1 is likely all you need. It cuts out the kettle and keeps the sink area tidy. If your household buys bottled water or keeps a filter jug topped up, the fourth function pays back in convenience, because that job moves to the tap.
A small office or shop
Staff make hot drinks all day and ask for cold water in summer. A 4 in 1 with chilled water serves both from one point. A touch-free model also helps keep a shared tap cleaner, since nobody has to grip a handle.
A larger workplace, school or care setting
The more people use the tap, the more the capacity of the boiler matters. The numbers in Zip model names, such as 240/175 or 100/75, are part of the specification, so check the product page against the headcount that will use the tap. If you are specifying for several sites or fitting out a block, speak to our trade team about bulk order pricing before you order.
A rental or a buy-to-let
Tenants like a tidy, modern kitchen. A 3 in 1 gives you the boiling-water feature with the least under-sink equipment, which keeps the cupboard usable.
Check the space under the sink
This is the step that catches people out. Both types need a boiler unit below the worktop, connected to the cold water supply and to a power socket. The 4 in 1 needs more again for the fourth function. Before you order, measure:
- The cupboard depth, width and height, allowing for pipework and the waste.
- Where the nearest socket is and whether it can be reached once the cupboard is in use.
- How many things already live there: bins, cleaning products, the waste disposal unit or the water softener.
- The worktop thickness and hole size the tap needs.
If the cupboard is already full, consider a 3 in 1, or move the clutter before you decide. Reaching for a 4 in 1 in a cramped unit can mean a messy install.
Also think about what comes out of the tap. If you are replacing a mixer tap, our guide to monobloc and mixer taps explains the spout and handle choices, which apply to the hot and cold side of any boiling tap.
What they cost to buy
Prices vary widely. Checkatrade’s 2026 cost guide puts the average boiling water tap at around £450, with entry-level models from about £250 and premium models from around £1,000 or more. A 4 in 1 normally sits higher in that range than a 3 in 1, because it carries more equipment. The same guide lists installation at around £50, with a call-out charge of around £110, though quotes differ by region and plumber.
When comparing, add up the whole job: the tap, the fitting, any extra filter or cartridge and, for the fourth function, any parts the model needs. Then divide by the years you expect to use it. Spread over a decade of daily use, the difference between the two types is small next to what it saves in kettles, bottles and time.
What they cost to run
A boiling tap keeps a tank hot, so it uses a little energy all day. A kettle uses energy only when you boil it, but it tends to boil more water than you need. The figures that get quoted come with dates, so treat them as a guide. In 2023, the Energy Saving Trust figure used by Ideal Home was about 0.2kWh for boiling a full kettle of around seven cups, costing roughly 7p at 34p per kWh. Electricity prices change with the energy price cap, which Ofgem updates every quarter, so recalculate with the unit rate on your own bill.
What matters when you compare the two taps:
- A 3 in 1 heats and holds the boiling tank. Nothing else uses power.
- A 4 in 1 with chilled water also runs a cooling function, so expect a modest extra on the electricity bill.
- Both can lose less heat if the tank is well insulated, so look for that in the specification.
- Both save water you would otherwise overfill the kettle with, because you take only what you need.
Filters, scale and looking after the tap
In hard water areas, scale builds up in a boiler over time. A filter in front of the unit protects the tank and keeps the water tasting clean. Our guide to water boiler filtration explains how to protect the system and when to think about it. Check the filter and cartridge schedule in the manual for the model you buy, and diarise the replacements so they are not missed.
If you are choosing a 4 in 1 because you want the fourth function to include filtration, confirm that it does, and which cartridge it takes, before ordering. If you are choosing a 3 in 1, the filtration guide above is still worth reading, because scale is a boiler problem, not a tap-type problem.
Installation and safety
Boiling water causes scalds, so installation is not a job to improvise. Checkatrade recommends hiring a qualified plumber for the tap and the under-sink unit, because you are fitting expensive equipment and working with boiling water, and because a professional fit helps keep the warranty valid. Use a plumber for the water connections and a qualified electrician if a new socket or spur is needed.
To use it safely day to day:
- Choose a model with a child safety lock on the boiling outlet. Our guide to the child lock on a boiling tap explains how it works and what to check.
- Keep the spout out of reach of small children, and teach everyone in the household or workplace how the lock works.
- Run the tap into a mug or pan, not into a hand or a sink that someone is standing next to.
A simple way to decide
Ask yourself these four questions.
- Do I want cold drinking water from the tap? If yes, a 4 in 1. If not, a 3 in 1.
- How many people will use it daily? The more people, the more the capacity and the touch-free option matter.
- How much room is under the sink? A tight cupboard points to the 3 in 1.
- What is the budget? A 3 in 1 costs less to buy and slightly less to run, and the 4 in 1 gives more in return.
If you answer yes to the first question and the cupboard allows it, buy the 4 in 1 the first time. Adding a fourth function later usually means replacing the tap, not upgrading it.
Where to buy your boiling water tap
We supply the Zip HydroTap models above to homeowners, facility managers and contractors across the UK, with fast UK delivery, a 30-day returns policy and bulk order pricing for trade buyers. Browse the Simco Direct range to see the 3 in 1 and 4 in 1 taps, along with the water heaters, bathroom products and washroom equipment that often go into the same project.

If you are fitting out an office, a school or several properties, tell us about the project and we will help with the specification and the order.
Our view
We think the right tap is the one people use without thinking about it. For most homes, a 3 in 1 does that: boiling water on demand, a clear worktop and no kettle to fill.
For workplaces, shared kitchens and families who drink a lot of water, the 4 in 1 earns its place. The extra function removes bottled water and jugs from the routine, and a touch-free model keeps a busy tap hygienic.
Whichever you choose, treat the under-sink space, the filter schedule and a qualified installer as part of the purchase, not afterthoughts. That is what makes a boiling tap trouble-free for years, and it is why we keep the Zip range, the filtration advice and the safety guidance together on one site.
Carl
FAQ
What is the difference between a 3 in 1 and a 4 in 1 tap?
A 3 in 1 gives boiling, hot and cold water. A 4 in 1 gives those three and a fourth type, which can be filtered, chilled or sparkling depending on the brand. Always check the product description to see which fourth function the model has.
Is a 4 in 1 tap worth the extra money?
It is if you drink cold water regularly or share the tap with many people. The fourth function can replace bottled water and jugs, and in an office it serves most of the drinks people ask for from one spot. If you only want boiling water, a 3 in 1 does the job for less.
Do I still need a kettle with a boiling water tap?
No. The tap supplies boiling water directly, so the kettle can go. Many households keep a kettle only as a backup, and it is no longer needed for daily drinks or cooking.
Can I fit a boiling water tap myself?
We advise using a qualified plumber, and an electrician if a new socket is needed. The tap uses boiling water and needs a connected under-sink unit, and a professional fit helps protect the warranty. Checkatrade gives around £50 for the installation in its 2026 guide, plus a call-out charge, so ask for a written quote.
Will a boiling tap fit under my sink?
The tap needs a boiler unit under the worktop, and a 4 in 1 normally needs more equipment than a 3 in 1. Measure the cupboard, check the socket position and compare it with the specification on the product page before ordering.
Sources
- Boiling Water Tap: Instant 100°C Water
- Boiling water tap: Cost breakdown 2026, Checkatrade
- Boiling water tap vs kettle: which uses less energy, Ideal Home
