Vented vs Unvented Boiling Taps: What the UK Rules Mean
A vented boiling water unit is open to the atmosphere. An unvented one is fed straight from the mains and sits under inlet water pressure. Most under-sink boiling taps in UK homes are the second kind: a small, sealed, mains-fed tank with safety valves. Which one suits you depends on how much boiling water you need, how much space and pressure you have, and whether the installation is for a kitchen or a busy washroom or staff area. We supply boiling water heaters and instantaneous water heaters for homes and commercial sites, so this guide sets out the checks we would want you to make before you order.
TL;DR
- Vented means the water store is permanently open to the atmosphere. Unvented means the store is under mains pressure and needs expansion and relief protection.
- Under the UK Water Fittings Regulations, a boiling tap with storage of any capacity counts as an unvented water heater, and one without storage counts as instantaneous.
- Small boiling-tap tanks sit below the 15 litre line at which extra notification rules for unvented vessels begin, but the Water Fittings Regulations still apply in full.
- Check clear space, a suitable electrical supply and incoming water pressure before choosing. Larger, busier sites should look at a higher-capacity boiling water heater.
- Child-safety features, filtration and descaling decide how well the tap lasts and how safely it is used.
Table of Contents
- What “vented” and “unvented” actually mean
- How a boiling tap works
- How UK regulations classify boiling taps
- Vented vs unvented boiling units side by side
- Pressure, flow and capacity
- Instantaneous heaters: the no-storage route
- Installation checks before you order
- Safety features that matter
- Home kitchen or commercial washroom?
- Keeping the system working
- Our boiling water range
- Our view
- FAQ
- Sources
What “vented” and “unvented” actually mean
The words come from hot water cylinders, and they carry over to boiling taps with the same logic.
A vented appliance is permanently open to the atmosphere. Water is not held under mains pressure, so there is always a route for air and expansion to escape. The Dutch certification body Kiwa, in its guideline for taps delivering hot or boiling water, defines it in exactly those terms.
An unvented appliance is subject to inlet water pressure. Cold water arrives from the mains, is heated in a sealed vessel, and leaves when you open the outlet. Because heated water expands and cannot escape on its own, the vessel needs an expansion device and a relief valve. Kiwa’s guideline requires expansion groups or valves on unvented units.
Picture a kettle with a lid that never closes (vented) against a pressure cooker with a safety valve (unvented). Both boil water. The engineering around them differs.

How a boiling tap works
The typical home boiling tap is a compact unvented system. Ideal Home describes an insulated tank under the sink, fed from the mains cold supply, in which an electric element heats water to roughly 96 to 100°C. When you draw some off, fresh cold water replaces it and the tank reheats, much like a large kettle that refills itself.
That is why the tap itself can be slim and sit on the worktop while the tank lives in the cupboard below. The pressure that pushes water out comes from the mains, not from a header tank in the loft.
How UK regulations classify boiling taps
In the UK the useful split is less “vented or unvented” and more “stored or not stored”. The September 2022 Water Regs UK guidance on multifunction taps classifies a boiling water tap with storage of any capacity as an unvented water heater, and one without storage as an instantaneous water heater. The whole installation is treated as a secondary hot water system under the Water Supply (Water Fittings) Regulations.
The same guidance sets out what that means in practice:
- Backflow protection, so water cannot be drawn back into the mains.
- A temperature control device.
- A temperature relief valve, or a combined temperature and pressure relief valve, for storage taps of any capacity.
- A pressure-activated expansion valve for instantaneous taps of 15 litres or more.
- A maximum water temperature of 100°C.
- Safe, conspicuous discharges, and measures to prevent water waste.
The temperature control and relief valve requirements come from Schedule 2, paragraph 17(1) of the Regulations, and the expansion valve requirement for 15 litres and over from paragraph 17(2).
So a small tank is not exempt. Whether the tank holds 3 litres or 10, it needs its protective devices.
The 15 litre threshold
Southern Water’s guide to the Water Fittings Regulations states that every unvented water heater or storage vessel over 15 litres must have a temperature control device, a temperature or combined temperature and pressure relief valve, an expansion valve, and an expansion vessel or integral expansion system. It adds that installers of unvented systems over 15 litres must notify the local authority and be a competent person.

In plain terms: a large unvented cylinder is a notifiable job. A compact boiling tap tank sits below that size, which is why a domestic installation is usually a straightforward fit. The regulations on backflow, valves and discharge still apply, so the work should follow them.
Vented vs unvented boiling units side by side
| Feature | Vented | Unvented |
|---|---|---|
| Relationship to atmosphere | Permanently open | Sealed, under inlet water pressure |
| Water source | Open outlet, not pressurised by the mains | Direct from the mains cold supply |
| Kiwa capacity limit | Up to 50 litres | Up to 15 litres |
| Expansion handling | Open to atmosphere | Expansion group or valve required |
| UK classification (Water Regs UK) | Not the typical under-sink design | Any tank with storage counts as unvented |
| Typical use | Larger water boilers where an open outlet is acceptable | Under-sink tanks behind a boiling tap |
The capacity figures in the table are Kiwa’s, a Dutch certification standard, and give a useful sense of scale: vented units are designed for larger volumes, and unvented units are kept small because a pressurised vessel carries more risk.
Pressure, flow and capacity
Pressure. An unvented tank uses mains pressure, so the flow at the tap is steady and does not depend on how high a tank sits above it. Boiling taps deliver water at lower operating pressure than a normal tap so it does not splash. Check the maker’s minimum incoming pressure before you buy, and measure your own supply if you are not sure.
Capacity. The tank size sets how much boiling water you get before the unit has to reheat. A small tank suits tea and coffee for a household. A kitchen or staff area serving many people in a short window needs more stored water, which is where a larger boiling water heater is the better match. Our Heatrae Sadia Supreme 180SS 7.5L Boiling Water Heater is one such option for sites that need more volume on hand.
Temperature. Kiwa’s guideline sets performance limits worth knowing as a yardstick: stored water at least 55°C, outlet temperature within 2°C of the claimed value, usable capacity at least 95% of the claimed volume, no steam in normal operation, and at least 1 litre per minute of flow for water above 65°C. Accessible surfaces should not exceed 65°C, and the actuating part not 45°C.
Space. Unvented tanks are compact, but they still need room for the tank, the valves and the pipework. Measure the cupboard height and depth, and leave room to reach the connections later.
Instantaneous heaters: the no-storage route
Because the regulations treat a tap without storage as instantaneous, this is a third option worth knowing. An instantaneous heater warms water as it flows, with no tank to fill and no standing stored volume. That suits locations where space is tight or demand is occasional, such as a small washroom or a utility sink.
We list several instantaneous options, including the DexPro Delux Inline Instantaneous Water Heater, the Stiebel Eltron DCE-S Plus Instantaneous Water Heater and the Perfect 35 Instant Water Heater 3.5kW. Remember the rule above: an instantaneous unit of 15 litres or more needs a pressure-activated expansion valve.
Installation checks before you order
Work through these in order. Each one is quicker to settle before delivery than after.
- Supply. Water Regs UK advises that where possible drinking water taps should be fed direct from the mains rather than via fittings that store, treat or filter the water. It also notes that a Type AUK 3 tap gap suits high-risk installations as backflow protection. Ask your installer how backflow protection is being met.
- Pressure. Confirm the incoming pressure meets the manufacturer’s stated minimum.
- Electrics. The tank needs a suitable electrical supply near the unit, and in a wet cupboard that is a job for a qualified electrician.
- Space. Measure clear height and width in the cupboard, including room for the filter and valves.
- Discharge. Relief valves must discharge safely and visibly. Plan where the pipe runs.
- Notification. If any single storage vessel is over 15 litres, the installer must be a competent person and notify the local authority.
- Worktop. Match the tap hole and finish to your sink. Our monobloc vs mixer tap guide helps with tap hole decisions.
A plumber for the water connection and an electrician for the supply are the right professionals for steps 1 to 5 in a home. For commercial sites, ask your facilities contractor to sign off the discharge and electrical details.
Safety features that matter
Boiling water at 96 to 100°C needs good design around it. According to Ideal Home, a typical tap uses a push-and-turn safety mechanism, and most have a built-in filter. Other features include key locks, removable clips and automatic shut-off. The two-step action is designed so boiling water flows only when you want it and are there to watch.
In a household with children, a washroom open to the public, or a staff kitchen, the child lock matters as much as the tank type. Our guide to child lock on a boiling tap explains how the mechanism works and what to check.
Home kitchen or commercial washroom?
Homeowners renovating a kitchen. An under-sink unvented tank behind a boiling tap is the usual choice: it saves worktop space, fills quickly and needs no loft tank. Check cupboard space and pressure, then decide on finish.
Landlords and property managers. Choose a unit with a lock feature, a filter and a size to match the number of occupants. Standardising on one model across units makes spares and servicing simpler.
Offices, staff rooms and facilities. Peak demand is the question: how many cups in how many minutes. A larger boiling water heater or a unit with more stored volume meets that better than a household tap.
Contractors. Specify the unit with the supply, pressure and discharge details agreed in advance, and ask us about bulk pricing on larger orders.
Keeping the system working
Hard water scales an element and cuts capacity, and unfiltered water shortens a unit’s life. Two of our guides cover this directly: water boiler filtration explains how a filter protects the system, and descaling commercial water boilers sets out the routine for sites with heavy use. Follow the manufacturer’s service interval for filter and valve checks.
Our boiling water range
We supply boiling water heaters, instantaneous water heaters and a wider range of washroom, heating and bathroom products for homes and commercial sites, with bulk order pricing for trade customers, fast UK delivery and a 30-day returns policy. Browse the Water Heaters category to compare units by capacity and size.

For a site that needs a higher volume of boiling water, start with the Heatrae Sadia Supreme 180SS 7.5L Boiling Water Heater. For a compact point-of-use heater, see the Stiebel Eltron DEM Set Mini Instant Water Heater.
Our view
We sell water heaters to homeowners, contractors and facility managers, and the question we hear most is how much boiling water a place really needs.
Our advice starts from the building, not the label. Work out how many people use the point, how often, and at what peak. Then match the tank or heater to that demand, and check supply, pressure and discharge on the same day.
For households, a compact mains-fed unit is usually the neat answer. For offices and busy washrooms, we point buyers to larger boiling water heaters and instantaneous units, because stored volume and recovery keep the queue moving. We offer bulk pricing for trade customers who are fitting several units at once.
Whatever the size, buy a unit whose valves, filter and safety features are clearly specified, and have it fitted by people who know the Water Fittings Regulations.
Carl
FAQ
Is a boiling water tap vented or unvented?
Most under-sink boiling taps are unvented: the tank is sealed and fed from the mains cold supply. Under the UK Water Fittings Regulations, a boiling tap with storage of any capacity is classed as an unvented water heater. One without storage is classed as instantaneous.
Do I need a competent person to fit an unvented boiling tap?
The extra notification and competent-person rules in the Southern Water guidance apply to unvented systems over 15 litres. Compact tanks sit under that figure. The Water Fittings Regulations still apply, including backflow protection and relief valves, so use a qualified plumber and electrician.
How much pressure does an unvented boiling tap need?
It depends on the manufacturer, so check the unit’s stated minimum incoming pressure before you buy. Because the tank is fed from the mains, low pressure can reduce flow and slow refilling.
What is the maximum temperature of a boiling tap?
Water Regs UK guidance sets a maximum of 100°C for boiling tap systems. Ideal Home describes typical taps delivering around 96 to 100°C. Safety mechanisms such as a push-and-turn action and a child lock are there to prevent accidental use.
Which is better for an office: a boiling tap or a boiling water heater?
For a few people, a tap with a small tank is enough. For a busy staff area, a larger boiling water heater holds more water and keeps up with peak demand. Match the capacity to the number of cups you need in your busiest ten minutes.
Sources
- Water Regs UK: Multifunction taps technical guidance, September 2022
- Water Regs UK: Drinking water taps
- Ideal Home: How do boiling water taps work?
- Kiwa BRL-K14040: Taps for delivery of hot or boiling water
- Southern Water: Water Supply (Water Fittings) Regulations guide
